BMX landing page
The Gyro G3 upper top plate is designed for use with the G3 detangler.
- Sold in pairs. - Allen wrench included.
Odyssey's Air Supply tubes are specifically sized to fit modern BMX tires, and they are manufactured with a stronger emphasis on quality versus simply chasing the lowest possible price. On average, the Air Supply BMX tube retains air significantly longer than others currently available on the market. This is down to both the rubber that is used, and because of strict quality control during manufacturing. It is normal to assume that a “tube is a tube,” but a higher quality tube will always last longer than a cheap tube during comparable everyday use.
When you can’t even see a part, you might forget about it, but it doesn’t mean its not important. Flat tires are probably the most common bicycle failures. Many times, flats are caused by the rims, specifically the lack of protection from the rims' sharp edges. Good rim strips didn’t exist for BMX rims. They work well and improve the function of any 20 inch rim. If you forget about them, that means they are doing their job.
Odyssey's custom-designed Par Ends come standard with all of their grips. Its special plastic composite will not shatter like cheap bar ends do, and they’re very lightweight. The Par End is a combination of the over-the-bar-style cap and the inside-the-bar-style to prevent the inner portion from blowing out like it does on ordinary press-fit bar ends. Comes stock on all of Odyssey's grips.
The Graduate sleeve is the replacement sleeve for the Graduate peg that's made from long lasting, fast sliding plastic. - Sold singly
Compatible cable for M2 Monolever.
Designed exclusively for use with the Kink Boulevard front hub, the Boulevard guard is injection molded from a durable nylon material. These guards slide directly over the existing hub hardware, so no additional parts or disassembly are required. This guard can be used on one or both sides of the Boulevard hub, providing protection where you need it.
Designed for use with Kink Incite rear hubs, the Incite Hub Guard is injection molded from a durable nylon material. This hub guard slides directly over the existing hub hardware, so no additional parts or disassembly are required. This guard fits the non-drive side of Kink rear hubs only.
Designed for use with both the Kink East-Coaster and Kink Yukon hubs, the Rear Guard is injection molded from a durable nylon material. This hub guard slides directly over the existing hub hardware, so no additional parts or disassembly are required. This guard fits the non-drive side of Kink rear hubs only.
$6.99 - $7.99
- Lower cables for Odyssey's Gyro G3 (sold separately). - Universal fit. - Lower cables only.
$6.99 - $7.99
- Upper cables for Odyssey's Gyro G3 (sold separately) - Universal fit. - Upper cables only.
$7.99 - $8.50 $8.50 Up to 6% Off
The Slim by Four is a BMX-specific brake pad with a symmetrical shape designed for both forwards and backwards braking. A custom inner frame helps to stiffen the pad and prevents excessive braking power from being lost to flex. SPECS - Clear and Gum colored “Soft” compound pads provide extra grip on powder coated rims. - Black “Normal” compound Slim-By-Four pads are the most popular pad choice for most riders.
Like WeThePeople? Then, put a WTP sticker on everything you own. This assorted pack includes a variety of designs and sizes.
One of the most important goals that Odyssey had when they sat down to work on new braking designs was to make the whole system easier to install (and remove) without sacrificing performance. They also wanted to be sure that every component would be very affordable too. The Ghost Pad addresses the hassles of brake pad installation by eliminating the traditional dome shaped washers used for toe-in. The pad improves stiffness by building the toe-in into the pad shape and utilizing a solid extruded aluminum frame at its core. The Ghost Pad’s assembly consists of simply lining it up with the rim and tightening down an M6 female bolt. Comes stock on the Springfield brake. SPECS Hardware: - In-bound bolt, 5mm Hex Key, M6x1.0 Thread - Pad Material: Black (standard) or Clear Rubber (Soft) - Weight: 1.0oz / 28g (pair)
The MK 4 version continues the GLAND’s heritage, but in a smaller and sleeker overall size which should appease many riders. The images beside show the top, profile, and under side of each guard.
Broc Raiford can bunnyhop over a house so it’s only right that he has his own grips to hold on to. Broc’s signature grip comes in at 160mm in length and features rope detailing on the ends to tie in with Broc’s nautical theme.
$9.99 - $22.99
- Press fit designed to work the hub's non-drive side collar.
The Odyssey K-Shield Linear cable features a pre-stretched inner Slic Kable covered in a linear casing to prevent binding and an outer K-Shield mesh housing for less weight over a standard steel mesh housing. (2.9 oz)
$9.99 $11.99 17% Off
- New ultra-slim 2014-T6 aluminum seat clamp with replaceable hardware and self-aligning nut. - 6061-T6 aluminum construction. - Standard 1-1/8-inch size.
$9.99 $9.99 - $11.99 Up to 17% Off
Tom Dugan’s signature grip features a timeless coil pattern, along with a feather design across the heavy wear areas. By using two molds you’ll notice feather angle symmetry once they’re installed. Par Ends included.
Sunday's Cornerstone Grips rock traditional styling, current branding, and come in at 150mm in length with plenty of color options. It's not a bad idea to keep an extra pair around.
The product designers at Sunday worked closely with Jake to nail down a grip that is perfect for him. Jake's grip comes in at 160mm and features a gradually increasing rib width. This grip can be run either way, depending on which side you prefer. The grip also features a tapered core for comfort.
WeThePeople's Arrow 115 Grips have the perfect texture and density to give you new confidence while railing it on the bike. Material: VEX rubber compound Rubber durometer: 30° Size: 115mm x 28mm Specials: soft angled rib design with medium-sized flange; includes WeThePeople nylon barends
WeThePeople's Arrow 146 Grips have the perfect texture and density to give you newfound confidence while railing it on the bike. Material: VEX rubber compound Size: 146mm x 28mm Specials: soft angled rib design with medium-sized flange; includes WeThePeople nylon barends
Check out the dinosaur skin-like texture of WeThePeople's Raptor grips! Like a raptor, you can wrap your claws around these grips and let the good times roll. The soft, VEX rubber compounds conforms perfectly to your hand, and holds up great to long days on the bike. • 150mm Long, 27.8mm Diameter • 30 durometer rubber • Low flange design • Includes WeThePeople nylon barends
$10.00 $16.95 41% Off
• Super lightweight design. • Very affordable & shin friendly. • Made from Nylon/Fibre mix. • Looseball axle type only in 9/16?. • Weight per pair: Nylon/Fibre mix 376 grams (13.26oz)
One of the most important goals that Odyssey had when they sat down to work on new braking designs was to make the whole system easier to install (and remove) without sacrificing performance. They also wanted to be sure that every component would be very affordable. The Springfield lever is easy to install and remove without having to wrestle grips on and off. An ordinary hinged clamp can be bulky and expensive so a new clamping design made specifically for die-casting was used. This approach keeps the lever reliable and affordable. The lever handle is the same comfortable shape as the proven Monolever Medium blade.
$10.99 $17.99 39% Off
The Odyssey Springfield U-brake turns the installation and adjustment of U-brakes into a quick and easy process that requires nothing more than a 5mm Allen key. By using a small center pull coil spring to attach both brake arms together, the Springfield brakes require no further spring tension adjustment. Cast aluminum arms help keep cost down without sacrificing brake stiffness and include Odyssey Ghost brake pads with integrated toe-in to further ease installation. Straddle cable, cable hanger and all necessary hardware included. For rear brake only.
The Maya grip features a proprietary DCR formula material in a honey comb pattern.
Page 1 of 6 Next page